You can examine this page dedicated to the firefighter clothes and equipment of firefighters, materials of the fire service, and the firefighter clothes and equipment, such as firefighter suits, firefighter helmets, and firefighter boots… Firefighters constitute the professional group that most needs the correct work clothes. This profession requires firefighters to fight against the flames, which makes job security an inescapable need.
That said, the simplest way to ensure job security is to bring clothes and appropriate firefighters’ equipment. We strive to produce structure firefighting suits, preciously. It is crucial to ensure that firefighter clothes and equipment are of good quality when purchased. We always use the best materials to produce a bunker coat that lives up to its image. Furthermore, going without saying, it should be mentioned that a bunker coat alone is not enough for a firefighter.
These people who are constantly fighting flames also need many accessories. Rubber fire boots are one of the most vital accessories for a firefighter. In addition, the firefighter’s helmet must also be worn by the firefighters. Our firefighter clothes and equipment have the following technical Information, firefighter clothes and equipment have a design that facilitates movement. It consists of two parts: a jacket and trousers. Moreover, it has four floors. Regarding the layer system, the Outer Layer has the following technical information, NOMEX OUTERSHELL TOUGH – 75% NOMEX®, 23% KEVLAR, 5% P 140.
The reflective trims are 3M fire retardant, 50 mm yellow-grey-yellow strip, the Moisture Barrier is made with FR mesh fabric + PU membrane. And concerning the inner layer, it is 50% Aramid and 50% Viscose FR. The Reflectors are, Yellow/gray/yellow, with aramid carrier. We also offer firefighter clothes and equipment such as fire extinguishers, and steel air-breathing tube sets. The steel air-breathing tube set has the following technical information, It is designed to protect people against airborne hazards in fire-fighting industrial environments or in fire-fighting environments where fire gases and fumes are present. 89/686 / EEC is a special design tube respiration system that is classified as Personal Protective Equipment.
It Conforms to EN 137 TYPE 2 / EN 139 standards and CE marked. And conforms to the MED directive as well. The Sigma 2 Type 2 set, is a simple and reliable two-stage pneumatic system. The first breath-activated positive pressure valve provides low breathing resistance and excellent performance, especially at high flow rates. In the first stage, the pressure-reducing valve only has two moving parts, accepting pressures of 300 bar without adjustment. The activation of the first breath varies from -20 to -30 bar. Also, The static positive pressure is between 1.0 and 4.0 bar. It Includes a non-adjustable, spring-loaded piston mechanism and a first-stage pressure relief valve with an output supply. The maximum working pressure is 450 bar the minimum blast pressure is 800 bar.
The length is 600mm, the Width is 278mm, and the depth (6.0 liter 200 bar cylinder) is 200mm. Also, the Cylinder (tube) connection device has a removable bronze filter. It is worth mentioning, that the steel air-breathing tube set is Equipped with a manual lock and an impeller valve. Moreover, it has an 1860-liter free air capacity and 46 minutes of usage. Rubber fireman boots have the following technical data, The Upper Part of the Drawing is Resistant to Flame, and Radiant Heat. The Boot Base is resistant to contact with hot surfaces. And also, the Steel Nose Is Resistant to 200 j. The Steel-Based Base Is Resistant to 1100 N Perforation. And the Boot Base, Is Resistant to oils.
It Has Cotton Inner Lining and Non-slip Sole. It is suitable, for use with chemical dressings, and is tested according to EN 943-5. In addition, it is resistant to fuel oil, Mineral oils, Acids, and Solvents. Full-face masks have been specially designed for use with all Scott air tube respirators, especially from professional firefighters, air-tube respirators and airline systems, and escape breathing apparatus. The full-face mask is positive pressure, the outer face seal is made of liquid silicone rubber and the inner mask is made of EDME material. The mask’s visor is made of scratches, and impact-resistant polycarbonate coated with a multi-curved and burnt-delay coating. The Visor is placed in place with U-shaped flaps.
Optionally, the right-hand port of the mask is also available if you want to install a communication kit. The speech diaphragm, mounted on the front of the mask, provides smooth speech and a low-resistance exhalation valve, that allows normal breathing, without additional effort. Heat and flame-resistant cap, that protects the user’s head and neck, against the negative effects of heat and flame are also crucial for firemen. The standards used for certification are; Certified according to EN ISO 13911 standards and carry CE marking.
